adjustment of clearance
英 [əˈdʒʌstmənt ɒv ˈklɪərəns]
美 [əˈdʒʌstmənt əv ˈklɪrəns]
【化】间隙调整
双语例句
- Improvement of measurement and adjustment of labyrinth clearance in turbine set
汽轮机组汽封间隙的测量与调整方法改进 - Since the adjustment of axial clearance of assembled turbodrill has great influence on its performance and service life, and the four-fulcrum thrust ball bearing pack has direct relation the axial clearance, a simulation of the axial distortion of the bearing is made by means of ANSYS software.
鉴于涡轮钻具装配时轴向间隙的调整对钻具性能和工作寿命有极大影响，而四支点推力球轴承组与轴向间隙有直接关系，为此选择求解精度较高的ANSYS软件对轴承组轴向变形进行仿真。 - The Adjustment for the Clearance of the Helix Cone Gear Mesh Side for the Reducer and the Clearance of Paired Cone Roller Bearings
减速机螺旋圆锥齿轮啮合侧间隙及成对圆锥滚子轴承间隙调整 - This article introduces the braking mechanism and main specifications of the brake and the automatic adjustment of wear-out clearance between the friction lining and brake disk.
阐述液压盘式制动器的制动原理和关键参数设计，并介绍摩擦片与制动盘在使用中磨损间隙的自动调整。 - Experience on the Adjustment of Roots Blower's Clearance
罗茨鼓风机的间隙调整 - During the installation of the spheres, the adjustment of every clearance and geometric dimension was strictly controlled and achieved good result.
在球罐安装过程中，严格控制各部间隙及几何尺寸的调整，取得了良好的效果。 - Improvement of the Behaviour of Rolling Bearing by Adjustment of Diametral Clearance
调整径向游隙提高滚动轴承性能的研究 - Study on Adjustment of Valve Clearance on Four-Stroke Internal Combustion Engines
四冲程内燃机气门间隙调整方法的探讨 - Design and adjustment of clearance of full suspension driving equipment for hollow axle wheel set motor
轮对空心轴式电动机全悬挂驱动装置间隙设计及调整 - Research on Process of Steam Gland Installation and Adjustment of Clearance
安装、调整汽封间隙的工艺、工装研究 - Study on Valve Timing and Fast Adjustment of Valve Clearance of Four-Stroke Internal Combustion Engines
四冲程内燃机配气相位与快速调整气门间隙的研讨 - Adjustment of Valve Clearance by Four-Step Method
气门间隙四次调整法 - The software can immediately give out optimal method of center adjustment, direction and values when accepting the values of labyrinth clearance and lower guide bearing center and eliminating the abnormal data.
软件在接受迷宫间隙和下导中心数据后，经过剔除异常数据，即时输出最佳中心调整方法、方向和数值。 - The rotor lobed, radial clearance calculation, end play orientation and adjustment, the determination of the meshing clearance between two rotors pressure angle of the Root's blower used for PTA conveying was discussed.
对PTA输送用罗茨鼓风机的转子叶型，径向间隙的计算，轴向间隙的定位，调整和两转子压力角位的啮合间隙的确定进行了讨论。 - Twice adjustment methods of valve clearance
一种气门间隙的两次调整法 - Adjustment of mesh clearance in cylindrical worm gears
圆柱蜗杆传动啮合侧隙的调整 - Adjustment of valves clearance for the in-line, V-type and number multi-cylinder engines is able to be completed only by rotating an engine twice and summed up in a pithy formula.
提出了一种利用简单口诀，对直列、V型及奇数多缸发动机，两次调校即可完成其所有气门调校的方法。 - Parameters adjustment and continuous feedback control strategy are studied, according to output variation of a vibro-impact system with clearance.
针对含间隙碰撞振动系统由于系统参数的变化，发生分岔和混沌这一实际情况，提出了系统参数依据系统输出的变化自动调节连续反馈控制的策略。 - Adjustment of the valve clearance and parking brake.
驻车制动的调整及制动液液位的检查等。 - The results show that the adjustment range of the pressure roller cea clearance can be enlarged, which makes the rolling equipment more universal.
扩大了辊压机械中压辊间隙的调整范围，使辊压机械设备具有通用性。 - Test and adjustment of assembling clearance of sliding bearing
滑动轴承装配间隙的测试与调整 - Fast Adjustment of Engine Valves Clearance
发动机气门的快速调整 - The causes of phase variation in air supply obtained after analysis are mainly errors in manufacture, abuse in operation and errors in repair. Several adjusting methods for correct installation of timing gears, inspection of meshing clearance of gear faces and adjustment of valve clearance are suggested.
分析了配气相位变化的原因主要是制造误差、使用不当和修配误差等，提出了正确安装正时齿轮、检查齿面啮合间隙和调整气门脚间隙等几种调整方法。